AP9617 MANUAL PDF

The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction. What is an instruction? A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

Author:Zulule JoJogore
Country:Iceland
Language:English (Spanish)
Genre:Automotive
Published (Last):18 September 2011
Pages:160
PDF File Size:14.70 Mb
ePub File Size:13.58 Mb
ISBN:303-7-75280-187-6
Downloads:32546
Price:Free* [*Free Regsitration Required]
Uploader:Kajind



Smart-UPS 1. Turn off the equipment that is connected to the UPS. Test Expansion chassis. Before you install the Management Card, put the UPS into bypass mode to continue to provide power to the load: 1.

Loosen the thumbscrew at the center of the back of the UPS to remove power from the electronics unit, which contains the slot for the Management Card. The isolation unit the part of the UPS below the thumbscrew continues to provide power to the load. Install the Management Card.

For instructions, see Installation in a UPS on page 6. At the back of the UPS, tighten the thumbscrew. Then respond to the prompt to take the UPS out of bypass mode. Note Disclaimer American Power Conversion is not responsible for damage sustained during reshipment of this product. The Network Management Card is sensitive to static electricity. When handling the Management Card, touch only the end plate while using one or more of these electrostatic-discharge devices ESDs : wrist straps, heel straps, toe straps, or conductive shoes.

Please recycle The shipping materials are recyclable. Save them for later use, or dispose of them appropriately. APC management products, including the Network Management Card, contain removable, lithium coin-cell batteries. When discarding these batteries, you must follow local rules for recycling. For instructions, see Installation in a UPS on page 6 3. Use the same screws that hold the slot cover in place to secure the Management Card in the UPS card slot.

Installation and Quick Start 2. See also Step 1: Disconnect the chassis from all power Make sure that the chassis is disconnected from any power source: Disconnect the chassis cable from the UPS. See also The Network Management Card is sensitive to static electricity. If a cable is connected to the serial port at the UPS or chassis, stop the APC service that uses that serial connection, and disconnect the cable.

If you are installing a chassis, connect the chassis to the UPS serial port. Use the same screws that hold the expansion slot cover in place to secure the Management Card in the chassis slot. Then connect the adapter to an independent AC input so that the Management Card can continue to operate if the UPS is turned off or fails.

If you disconnected a cable in step 1, reconnect that cable to the serial port at the chassis, and restart the associated APC service. See Quick Configuration on page The Management Card uses Note the default gateway to test the network when traffic is very light.

Do not use the loopback address See Watchdog Features in the Introduction of the Network Management Card Users Guide for more information about the watchdog role of the default gateway. Local computer See Local access to the control console on page Networked computer See Remote access to the control console on page Most software firewalls must be temporarily disabled for the Wizard to discover unconfigured Network Management Cards.

Note 1. When the Wizard discovers the unconfigured Management Card, follow the on-screen instructions. If you leave the option Start a Web browser when finished enabled, you can access the Management Card through your browser by using apc the default for both the user name and password.

The Management Card assumes all settings specified in the bootup file. If you did not specify a bootup file name, you can configure the other settings of the Management Card remotely through its Web interface or control console; user name and password are both apc, by default. See also 1. Select a serial port at the local computer, and disable any service that uses that port.

Use the configuration cable to connect the selected port to the serial port on the front panel of the Management Card. Run a terminal program such as HyperTerminal and configure the selected port for bps, 8 data bits, no parity, 1 stop bit, and no flow control.

Save the changes. Use apc for the user name and password. See Control console on page 16 to finish the configuration. Note For example, to define

IGCT DATASHEET PDF

Network Management Card v3.7.2 Firmware for Smart-UPS with AP9617/8/9

.

INTRODUCTION TO INTERNATIONAL POLITICAL ECONOMY BALAAM DILLMAN PDF

APC AP9617 Network Card User Manual

.

LIBRO TEOLOGIA BIBLICA Y SISTEMATICA MYER PEARLMAN PDF

APC AP9617 manual

.

ICL7611 DATASHEET PDF

APC Network Card AP9617 user guide

.

Related Articles